Enweld Technologies

Enweld Capabilities

We Provide state-of-art infrastructure and designing capabilities, supported by strong processes and a motivated workforce to help clients with complex requirements

Welding

Works Certification
#ISO 9001 : 2008

Manual Welding

Welding Stations: 5+ MIG (Argoshield) welding stations
Welding Equipment: 100+ 600VA/400VA MIG Welding Equipment from Fronius-Austria; Miller-USA and ESAB-India;600VA Pulse Synergic Welding Machine

Machining

Machining of 1.8M diameter shell	MAKE: BERTHIEZ TYPE: VERTICAL TURRET LATHE (V.T.L) ID No: VTL – 4 Specifications: Chuck Dia (Ø): 3610mm Swing over bed: 6300mm Admit (daylight): 3900mm	MAKE: SEDIN TYPE: VERTICAL TURRET LATHE (V.T.L) ID No: VTL – 5 Specifications: Chuck Dia (Ø): 2400mm Swing over bed: 3100mm Admit (daylight): 1700mm	MAKE: FRORIEP TYPE: VERTICAL TURRET LATHE (V.T.L) ID No: VTL – 2 Specification: Chuck Dia (Ø): 3000mm Swing over bed: 3300mm Admit (daylight): 3000mm
MAKE: SCHIESS TYPE: VERTICAL TURRET LATHE (V.T.L) Specification: Chuck Dia (Ø): 2500mm Swing over bed: 2600mm Admit (daylight): 1500mm	MAKE: SCHARMANN FB 132 TYPE: HORIZONTAL BORING (H.B) ID No: H.B – 2 Specifications Bed: 1800mm*2000mm Spindle Dia: 132mm Travers X-Axis: 1900mm Y-Axis: 1500mm Z-Axis: 1250mm	MAKE: TOSS TYPE: FLOOR BORING (F.B) Specifications Spindle Dia: 130mm Travers X-Axis: 5000mm Y-Axis: 2300mm Z-Axis: 1200mm	MAKE: SCHARMANN FB 132 TYPE: HORIZONTAL BORING (H.B) ID No: H.B – 2 Specifications Bed: 1800mm*2000mm Spindle Dia: 132mm Travers X-Axis: 1900mm Y-Axis: 1500mm Z-Axis: 1250mm

Finishing

Stress Relieving
- Job Maximum Size : 12x3.5x2.5 Mtr.
- Bogie Capacity : 20 Ton
- Operating Temperature : 640 c
- Type of Furnace : Diesel Fire
- No. of Thermocouples : 18 Noo.s
- Type of Burner : High Velocity Duel Fuel Burner
- Heat Cycle Chart : 18 points recorder with print out option
- Process Control : Fully Automatic
- Temperature Control Concept : The Furnace Temperature control concept is effected by means of a fully automatic control system through the 4 zones.
Typical Heat Treating Cycle
- Heating to the Control Temperature
- Holding at Temperature
- Cooling (Rapid or at SLow / Controlled Rate)
Sand Blasting
Painting

Painting Done By Professionals

Design & Capabilites

Pre Fabricated Buildings
Heat Exchangers
Pressure Vessels
Production Engineering

Our production engineers enable us to develop fixtures and tools, optimize production process and minimize wastage. We have resources specialized in:
- Nesting
- Process Sheets
- Process Flow Optimization
- Measurement
- Control
Computer Aided Engineering

Through its stake in TimeTooth, MIC has access to cutting edge CAE solutions. Sample case undertaken:
- Segment: Material Handling
- Challenge: Predict structural strength of two frame split-chassis of crane and identify stress hotspots
- Outcome: Identified areas where stress levels were higher than target numbers; suggested and applied design improvements